2018年第65回応用物理学会春季学術講演会

講演情報

一般セッション(ポスター講演)

13 半導体 » 13.7 化合物及びパワー電子デバイス・プロセス技術

[17p-P12-1~27] 13.7 化合物及びパワー電子デバイス・プロセス技術

2018年3月17日(土) 16:00 〜 18:00 P12 (ベルサール高田馬場)

16:00 〜 18:00

[17p-P12-18] Excimer laser annealing of Mg-implanted GaN films

Juan Paolo Soria Bermundo1、Yuki Tada1、Hiroshi Ikenoue2、Mutsunori Uenuma1、Yasuaki Ishikawa1、Yukiharu Uraoka1 (1.NAIST、2.Kyushu Univ.)

キーワード:GaN, low temperature annealing, laser annealing

     GaN is a very attractive material with extensive application in short wavelength light-emitting diodes and next-generation high power devices due to its outstanding properties such as large breakdown field, high-speed switching, minimal on-resistance, and wide bandgap. For better turn on voltage control, performance, and prevention of current collapse, p-type GaN has been used in various configurations. A great challenge with p-type GaN especially those obtained through Mg implantation is the difficulty to activate Mg substituted at the Ga site (MgGa) to reliably obtain p-type conductivity. Other defects introduced during ion implantation such as N vacancies and Ga vacancies have also been shown to inhibit p-type conductivity and decrease Photoluminescence (PL) intensity [1]. Thus, high temperature annealing (>500 °C) is typically required to activate dopants and recover defects introduced by implantation [2].
     In this study, we employed excimer laser annealing (ELA) to irradiate and anneal a 500 nm Mg-implanted GaN layer on a GaN substrate. Samples were irradiated with either 1 shot at a fluence (F) of 600 mJ/cm2 or 10 shots at F = 375 mJ/cm2 in a vacuum or Ar (Table 1) by a KrF excimer laser (λ = 248 nm, pulsewidth = 9 ns). We analyzed the ELA’s effect on the optical, physical, and chemical properties of GaN by performing Ellipsometry, PL, simulation, and X-ray photoelectron spectroscopy (XPS) measurements.
     Fig. 2 is the laser-induced temperature at the Mg-implanted GaN surface estimated by COMSOL Simulation. Large induced temperatures of 1200 K in ~100 ns imply that ELA can be a rapid activation annealing alternative to typical lengthy activation methods. Ellipsometry analysis show that prior to ELA, Mg-implanted GaN had a bandgap (Eg) of 3.34 eV. After ELA, only GaN-1 showed a large Eg reduction to 3.16 eV. Furthermore, PL measurements reveal higher PL intensity at ~3.38 eV after ELA in Ar. Ga 3d XPS spectra (Fig. 3) of ELA samples are broader and shift to lower binding energy compared with bare GaN (no implantation and no ELA) suggesting lower Ga-N and higher metallic Ga (Ga-Ga) concentrations for ELA samples. The results and analysis herein are crucial in developing rapid activation annealing of p-type GaN
[1] K. Kojima et al. Appl. Phys. Express 10, 061002 (2017)
[2] T. Niwa et al. Appl. Phys. Express 10, 091002 (2017)
We thank Fuji Electric Co., Ltd. for providing the Mg-implanted GaN substrates.
This work was supported in part by the Council for Science, Technology and Innovation (CSTI), Cross-ministerial Strategic Innovation Promotion Program (SIP), “Next-generation power electronics-Research and Development of Fundamental Technologies for GaN Vertical Power Devices” (funding agency: NEDO).