International Session

[IS] International Session(2)　Cutting-Edge Science and Technology in Additive Manufacturing（2）

Fri. Sep 22, 2023 1:00 PM - 5:35 PM Rm. A (1st Flr. Education and Research Building, School of Engineering)

Chair: Naoyuki NOMURA (Tohoku Univ., Japan), Hyoung Seop KIM (POSTECH, Korea), Yuichiro KOIZUMI (Osaka Univ., Japan)

※表示の講演時間には質疑応答時間も含みます。
（質疑応答時間5分、基調講演と招待講演は5～10分）

+Add all to schedule

1:00 PM - 1:30 PM

[IS15] Development of High Strength Al-Si-Mg Powders for Additive Manufacture

*Chun-mu CHEN¹, Chi-San CHEN¹, Yu-Hsien CHOU¹, Hsin-Hwa CHEN¹ (1. Materials and Chemical Research Laboratories Industrial Technology Research Institute, Taiwan)

1:30 PM - 2:00 PM

[IS16] Design of Aluminum Alloys for both High-Temperature Strength and Sufficient Printability of Laser Powder Bed Fusion

*Naoki Takata¹, Wenyuan Wang², Miyawaki Takanobu², Yue Cheng², Asuka Suzuki¹, Makoto Kobashi¹, Masaki Kato³ (1. Nagoya Univ., Japan, 2. Nagoya Univ., Japan (Graduate Student), 3. Aichi Center for Industry and Science Technology)

break (2:00 PM - 2:15 PM)

2:15 PM - 2:45 PM

[IS17] Mitigating Gas Pores in Electron Beam Powder Bed Fusion

*Kenta Yamanaka¹, Shoya Aota¹, Haruko Numata¹, Yujie Cui¹, Yufan Zhao¹, Manami Mori², Jérôme Adrien³, Eric Maire³, Damien Fabrègue³, Akihiko Chiba^1,4 (1. IMR, Tohoku Univ., Japan, 2. NIT Sendai Col., 3. INSA Lyon, France, 4. NICHe, Tohoku Univ., Japan)

2:45 PM - 3:15 PM

[IS18] Post-treatments of Laser Metal Deposited Inconel 738 LC Weld

*H.W. CHEN¹, M.S. LEU², *J.K. CHEN³ (1. National Taipei Univ. of Technology, Taiwan (Graduate Student), 2. Industrial Technology Research Institute, Taiwan, 3. National Taipei Univ. of Technology, Taiwan)

3:15 PM - 3:45 PM

[IS19] Opportunities and Challenges of Wire Arc Additive Manufacturing

*Huijun LI¹ (1. Univ. of Wollongong, Australia)

break (3:45 PM - 4:00 PM)

4:00 PM - 4:30 PM

[IS20] Progress of Material Extrusion Additive Manufacturing for Metal in Thailand

*Chanun SUWANPREECHA¹, Sukrit SONGKUEA¹, Siwat LINJEE¹, Suksan MUENGTO¹, Anchalee MANONUKUL¹ (1. National Metal and Materials Technology Center, National Sciences and Technology Development Agency, Thailand)

4:30 PM - 5:00 PM

[IS21] Hetero-Microstructure Effect on the Mechanical and Corrosion Properties of Directed Energy Deposition-Processed Ti-Zr-Nb-Sn Alloy

*Jung Gi KIM¹, Yukyeong LEE¹, Shuanglei LI², Taekyung LEE³, Jeong　Seok OH¹, Jun-Seob LEE⁴, ae-Hyun NAM¹ (1. Gyeongsang National Univ., Korea, 2. Korea Inst. of Materials Science, Korea, 3. Pusan National Univ., Korea, 4. Changwon National Univ., Korea)

5:00 PM - 5:30 PM

[IS22] Additive Manufacturing of Low Alloy Steel Parts by Laser Based Directed Energy Deposition

*Monideepa MUKHERJEE¹, Ajit Hanumant SHINDE¹, Vamsi Krishna　BALLA², Mitun DAS² (1. R&D, Tata Steel, India, 2. CSIR- CGCRI, India)

Opening address (5:30 PM - 5:35 PM)

Session information

[IS] International Session(2)　Cutting-Edge Science and Technology in Additive Manufacturing（2）

[IS15] Development of High Strength Al-Si-Mg Powders for Additive Manufacture

[IS16] Design of Aluminum Alloys for both High-Temperature Strength and Sufficient Printability of Laser Powder Bed Fusion

[IS17] Mitigating Gas Pores in Electron Beam Powder Bed Fusion

[IS18] Post-treatments of Laser Metal Deposited Inconel 738 LC Weld

[IS19] Opportunities and Challenges of Wire Arc Additive Manufacturing

[IS20] Progress of Material Extrusion Additive Manufacturing for Metal in Thailand

[IS21] Hetero-Microstructure Effect on the Mechanical and Corrosion Properties of Directed Energy Deposition-Processed Ti-Zr-Nb-Sn Alloy

[IS22] Additive Manufacturing of Low Alloy Steel Parts by Laser Based Directed Energy Deposition

Authentication

Session information

[IS] International Session(2) Cutting-Edge Science and Technology in Additive Manufacturing（2）

Authentication

[IS] International Session(2)　Cutting-Edge Science and Technology in Additive Manufacturing（2）