深化と進化、未来を創る両利きの射出成形技術

Thu. Jun 20, 2024 1:30 PM - 2:50 PM Room A (3階　瑞雲)

座長:木村文信(東京大学)

+Add all to schedule

1:30 PM - 1:50 PM

[A-205] Fiber orientation analysis considering pressure dependence of flow yield value in composites

*Masato Goto¹, Hisahiro Tanaka¹, Motonori Nakai¹, seonggyun jeong¹, Masaki Yoshii¹, Masahiro Seto², Masashi Yamabe² (1. SAEILO JAPAN inc., 2. Kanazawa Insitute of Technology Univ.)

1:50 PM - 2:10 PM

[A-206] Observation of fiber orientation behavior during injection molding and consideration of prediction for fiber orientation

*Taiki Miyajima¹, Masahiro Seto¹, Masashi Yamabe¹ (1. Kanazawa Institute of Technology)

2:10 PM - 2:30 PM

[A-207] Fabrication of A Hollow Microneedle with Jagged Edges Mimicking Mosquito by Thermal Nanoimprinting Method Using A Mold Combining Different Rigid Materials

*Seiji Aoyagi¹, Jinya Sakamoto¹, Natsuo Otera¹, Tomokazu Takahashi¹, Masato Suzuki¹ (1. Kansai University)

2:30 PM - 2:50 PM

[A-208] Development of a New Micro Injection Mold Using CIM Technology and PDMS
- Fabrication of microneedles made of polylactic acid that mimic mosquito mouthparts -

*Seiji Aoyagi¹, Daisuke Yamaguchi¹, Shintaro Kaku¹, Natsuo Otera¹, Yuki Nakata¹, Tomokazu Takahashi¹, Masato Suzuki¹, Koichiro Suzuki², Zenku Haga³, Yoshihiro Tanigawa⁴ (1. Kansai Univ., 2. Musashino Chemical Laboratory, Ltd, 3. Meiho Co., Ltd, 4. Fukuoka Industrial Technology Center)

Session information

深化と進化、未来を創る両利きの射出成形技術

[A-205] Fiber orientation analysis considering pressure dependence of flow yield value in composites

[A-206] Observation of fiber orientation behavior during injection molding and consideration of prediction for fiber orientation

[A-207] Fabrication of A Hollow Microneedle with Jagged Edges Mimicking Mosquito by Thermal Nanoimprinting Method Using A Mold Combining Different Rigid Materials

[A-208] Development of a New Micro Injection Mold Using CIM Technology and PDMS
- Fabrication of microneedles made of polylactic acid that mimic mosquito mouthparts -

Authentication

Session information

深化と進化、未来を創る両利きの射出成形技術

[A-205] Fiber orientation analysis considering pressure dependence of flow yield value in composites

[A-206] Observation of fiber orientation behavior during injection molding and consideration of prediction for fiber orientation

[A-207] Fabrication of A Hollow Microneedle with Jagged Edges Mimicking Mosquito by Thermal Nanoimprinting Method Using A Mold Combining Different Rigid Materials

[A-208] Development of a New Micro Injection Mold Using CIM Technology and PDMS- Fabrication of microneedles made of polylactic acid that mimic mosquito mouthparts -

Authentication

[A-208] Development of a New Micro Injection Mold Using CIM Technology and PDMS
- Fabrication of microneedles made of polylactic acid that mimic mosquito mouthparts -