1: 射出成形

Wed. Dec 1, 2021 3:30 PM - 5:10 PM Room F (Online)

座長:瀬戸雅宏(金沢工業大学)

+Add all to schedule

3:30 PM - 3:50 PM

[F-215] Development of Direct Molding of Dry Blend Low Materials Using Vent Molding System Ⅱ

*Akio Kataoka¹, Keigo Nishitani¹, Rie Nobe², Makoto Kudo², Satoshi Nagai³ (1. Nihon Yuki Co., Ltd., 2. Akita Industrial Technology Center, 3. Mitsubishi Gas Chemical Trading, Inc.)

3:50 PM - 4:10 PM

[F-216] Influence of secondary weld line on appearance quality in injection molding Ⅱ
- Investigation of suppression effect of secondary weld line height focusing on thickness of resin confluence -

*Hideaki Hayashi¹, Atsushi Mizutani¹, Ryoichi Takatsu¹, Susumu Takahashi², Kosuke Suzuki² (1. Nissan Motor Co., Ltd., 2. Nihon University)

4:10 PM - 4:30 PM

[F-217] The Simulation of Melting State via a Plasticizing Process and Optimization by using the Mathematical Programing

*Makoto Kozuka¹, Chiharu Nishizawa¹ (1. Nissei Plastic Industrial CO.,LTD.)

4:30 PM - 4:50 PM

[F-218] Multi-objective optimization in rapid heat cycle molding incorporating variable packing pressure for improving weldline, cycle time and clamping force

*Shogo Tsurita¹, Satoshi Kitayama¹, Masahiro Takano², Yusuke Yamazaki³, Yoshikazu Kubo³, Shuji Aiba³ (1. Kanazawa Univ., 2. Industrial Research Institute of Ishikawa, 3. Sodick Co., Ltd.)

4:50 PM - 5:10 PM

[F-219] Machine learning based robust optimization for injection molding

*Hiroki Oka¹, Yusuke Uchiyama¹, Takanori Kadoya¹, Takekazu Sawa² (1. MAZIN, Inc., 2. Shibaura Institute of Technology)

Session information

1: 射出成形

[F-215] Development of Direct Molding of Dry Blend Low Materials Using Vent Molding System Ⅱ

[F-216] Influence of secondary weld line on appearance quality in injection molding Ⅱ
- Investigation of suppression effect of secondary weld line height focusing on thickness of resin confluence -

[F-217] The Simulation of Melting State via a Plasticizing Process and Optimization by using the Mathematical Programing

[F-218] Multi-objective optimization in rapid heat cycle molding incorporating variable packing pressure for improving weldline, cycle time and clamping force

[F-219] Machine learning based robust optimization for injection molding

Authentication

Session information

1: 射出成形

[F-215] Development of Direct Molding of Dry Blend Low Materials Using Vent Molding System Ⅱ

[F-216] Influence of secondary weld line on appearance quality in injection molding Ⅱ- Investigation of suppression effect of secondary weld line height focusing on thickness of resin confluence -

[F-217] The Simulation of Melting State via a Plasticizing Process and Optimization by using the Mathematical Programing

[F-218] Multi-objective optimization in rapid heat cycle molding incorporating variable packing pressure for improving weldline, cycle time and clamping force

[F-219] Machine learning based robust optimization for injection molding

Authentication

[F-216] Influence of secondary weld line on appearance quality in injection molding Ⅱ
- Investigation of suppression effect of secondary weld line height focusing on thickness of resin confluence -