2:40 PM - 3:10 PM
*Takayoshi NAKANO1 (1. Osaka University, Graduate School of Enging.)
Session information
一般講演
7.Biomedical and Health Care » Biomaterials Development and Clinics
[G] Biomaterials Development and Clinics(1)
Thu. Sep 19, 2024 2:40 PM - 5:45 PM Room A (A001 basement 1st floor Building A Center for Education in Liberal Arts and Sciences)
座長:成島 尚之(東北大学)、野村 直之(東北大学)、堤 祐介(国立研究開発法人 物質・材料研究機構)
※表示の講演時間には質疑応答時間も含みます。
（質疑応答時間5分、基調講演と招待講演は5～10分）
3:10 PM - 3:25 PM
*Her-Hsiung Huang1, Chia-Fei Liu1 (1. Department of Dentistry, National Yang Ming Chiao Tung University, Taipei, Taiwan)
3:25 PM - 3:40 PM
*Sungho Lee1, Minori Takahashi2, Akiko Obata2, Fukue Nagata1 (1. AIST, 2. Nagoya Institute of Technology)
break (3:40 PM - 3:50 PM)
3:50 PM - 4:05 PM
*Jun Rey Sullano LINCUNA1, Kyosuke UEDA2, Takayuki NARUSHIMA2 (1. Department of Materials Processing, Graduate School of Engineering, Tohoku University (D)、2. Department of Materials Processing, Graduate School of Engineering, Tohoku University)
4:05 PM - 4:20 PM
*Kohei HOSOKI1, Akiko OBATA2 (1. Nagoya Inst. of Technol., 2. Nagoya Inst. of Technol.)
4:20 PM - 4:35 PM
*Ryosuke OZASA1,2, Akira Hyakubu1, Takayoshi Nakano1,2 (1. Osaka Univ. Grad. Eng., 2. Osaka Univ. AM Center)
4:35 PM - 4:50 PM
*Yusuke TSUTSUMI1, Masaya Shumabukuro2, Tomoyo Manaka3, Mitsuhiro Goto4, Mariko Kadowaki1, Hideki Katayama1, Masakazu Kawashita2, Takuya Ishimoto3, Takao Hanawa2,5,6 (1. NIMS, 2. Tokyo Med Dent Univ, 3. Univ Toyama, 4. Fuji Koushuha KK, 5. Osaka Univ, 6. Kobe Univ)
break (4:50 PM - 5:00 PM)
5:00 PM - 5:15 PM
*Tomoki Nakajima1, Kosuke Ueki2, Kyosuke Ueda3, Takayuki Narushima3 (1. Graduate School of Engineering, Tohoku Univ. (M), 2. Graduate School of Science and Engineering, Kindai Univ., 3. Graduate School of Engineering, Tohoku Univ.)
5:15 PM - 5:30 PM
*Tomoki Wada1, Kyosuke Ueda2, Takayuki Narushima2 (1. Graduate School of Engineering, Tohoku Univ. (M), 2. Graduate School of Engineering, Tohoku Univ.)
5:30 PM - 5:45 PM
*Ozkan Gokcekaya1,2, Yong Seong Kim1, Rosuke Ozasa1,2, Aira Matsugaki1,2, Takayoshi Nakano1,2 (1. Osaka University, Graduate School of Engineering, 2. Osaka University, Additive Manufacturing Center)