公募シンポジウム講演

[S2] Materials science of additive manufacturing for biomedical and welfare applications (part IV)

Thu. Mar 18, 2021 1:00 PM - 4:55 PM Rm. B (ZoomRm.B)

座長:石本卓也(大阪大学)、堤祐介(国立研究開発法人　物質・材料研究機構)

※表示の講演時間には質疑応答時間も含みます。
（質疑応答時間5分、基調講演と招待講演は5～10分）

+Add all to schedule

1:00 PM - 1:20 PM

[S2.5] Effect of water quench heat treatments on microstructure and mechanical properties of
EBM-built Ti-6Al-4V

*SRI　NAGA　SESHA KARRI¹, Kenta Yamanaka¹, Kenta Aoyagi¹, Akihiko Chiba¹ (1. Institute for Materials Research,Tohoku University)

1:20 PM - 1:40 PM

[S2.6] Microstructure and mechanical properties of graphene oxide/titanium composites fabricated by laser additive manufacturing

*Mingqi Dong¹, Weiwei Zhou², Naoyuki Nomura² (1. 東北大工（院生）、2. 東北大工)

1:40 PM - 2:00 PM

[S2.7] Evaluation of Ti alloy powder properties and its powder bed condition for additive manufacturing

*Kohei KAMATA¹, Yohito MASUDA¹, Daiki WADA¹, Weiwei ZHOU¹, Naoyuki NOMURA¹ (1. Tohoku Univ.)

2:00 PM - 2:25 PM

[S2.8] Effect of mechanical stimulation on the electrical properties of the surface oxide film of Ti6Al 4V alloy powder

Ayane Sukegawa¹, Kenta Aoyagi², Keiji Yanagihara², Fangzhou Liu¹, Keisuke Ito³, *Akihiko Chiba² (1. Tohoku Univ., 2. Institute for Materials Research, 3. Miyagi Industrial Technology Institute)

2:25 PM - 2:40 PM

[S2.9] Microstructure and Mechanical Properties of TiAl4822 Built by Selective Laser Melting

*MIZUTA KAZUHIRO¹, FUJII TATSUYA¹, HIJIKATA YUTA³, GOKAN KAZUHIRO¹, KAKEHI KOJI² (1. Tokyo Metropolitan University, 2. Tokyo Metropolitan University, 3. Tokyo Metropolitan University)

break (2:40 PM - 3:00 PM)

3:00 PM - 3:20 PM

[S2.10] Fabrication of 3D tissue-like constructs using soft materials

*Masaya Yamamoto ^1,2 (1. Grad. School Eng., Tohoku Univ. , 2. Grad. School Biomed. Eng., Tohoku Univ.)

3:20 PM - 3:35 PM

[S2.11] Design of Anisotropic Mechanical Function in β-Type Ti Alloy via Selective Laser Melting (SLM)

*Naotaka MORITA¹, Takuya ISHIMOTO¹, Kouta KIMURA¹, Takayoshi NAKANO¹ (1. Osaka Univ.)

3:35 PM - 3:55 PM

[S2.12] Analysis of Crystallographic Texture Formation in Metal Additive Manufacturing Using Thermal Diffusion Simulation

*Takuya ISHIMOTO¹, Ryoya SUGANUMA², Takayoshi NAKANO¹ (1. Osaka Univ., Graduate School of Engineering)

3:55 PM - 4:15 PM

[S2.13] Microstructure, Corrosion Resistance and Mechanical Properties of Additively Manufactured Austenitic Stainless Steel

*Akira Otsu¹, Masahiro Hayashi¹, Tetsuhiko Onda¹, Zhong-Chun Chen¹ (1. Tottori Univ.)

4:15 PM - 4:55 PM

[S2.14] [Keynote Lecture]Development of new alloy for Additive Manufacturing

*Shinya Imano¹, YuTing Wang¹, Takashi Shibayama¹, Atsuo Ota¹ (1. Mitsubishi Power)

Session information