General Session: Forming and Sintering

Tue. Nov 19, 2024 9:15 AM - 10:35 AM Room III (3F, Room 301)

Chairperson:Sota TERASAKA(Japan Fine Ceramics Center)

+Add all to schedule

9:15 AM - 9:30 AM

[3-1A] DIC analysis of sintering deformation behavior in stepped powder compacts with inhomogeneous density distribution 《 Sintering 》

*Yamato Ikeda¹, Kentaro Kudo², Noriharu Yodoshi², Kazunari Shinagawa² (1. Graduate School of Kyushu University, 2. Kyushu University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)

9:30 AM - 9:45 AM

[3-2A] mechanical performance evaluation of micro-powder using force-displacement curve obtained from compression tests 《 Physical Property, Evaluation Technology 》

*Tao ZHANG¹, Weiwei Zhou¹, Naoyuki Nomura¹ (1. Tohoku University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)

9:45 AM - 10:00 AM

[3-3A] Hot compressive deformation behavior of metallic glass composites under rapid heating condition. 《 Sintering 》

*Tatsuya Kikkawa¹, Noriharu Yodoshi², Kentaro Kudo², Kazunari Shinagawa² (1. Graduate School of Kyushu University, 2. Kyushu University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)

10:00 AM - 10:10 AM

[3-4B] A fast and accurate method for density measurement 《 Evaluation Technology 》

HIROFUMI SHINTOKU¹, *AKIRA SHIMADA¹ (1. TOYOTA MOTOR CORPORATION)

10:10 AM - 10:25 AM

[3-5A] Influence of Pore Size Distribution on Fatigue Strength in Injection Molded High-Hardness Steel 《 Sintering, Physical Property 》

*Hayato Koyaishi¹, Kentaro KUDO², Noriharu YODOSHI², Kazunari SHINAGAWA² (1. Graduate School of Kyushu University, 2. Kyushu University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)

Break（10min）（10:25 AM - 10:35 AM）

General Session: Forming and Sintering

Tue. Nov 19, 2024 10:35 AM - 11:50 AM Room III (3F, Room 301)

Chairperson:Kazunari SHINAGAWA(Kyushu University)

+Add all to schedule

10:35 AM - 10:50 AM

[3-6A] Three-dimensional structural analysis and characteristic prediction of open-pore porous materials utilizing deep generative model and homogenization method 《 Physical Property, Evaluation Technology, Computational Science 》

*Itsuki Kato¹, Asuka Suzuki¹, Naoki Takata¹, Makoto Kobashi¹ (1. NAGOYA UNIVERSITY）（※This presenter is a candidate for the Student Award for Outstanding Presentation.　)

10:50 AM - 11:05 AM

[3-7A] Fabrication of porous (Al, Fe)₃Ti with various compositions through reactive sintering with space holder. 《 Sintering, Physical Property 》

*Taiga Yamazaki¹, Asuka Suzuki¹, Naoki Takata¹, Makoto Kobashi¹ (1. Nagoya University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)

11:05 AM - 11:20 AM

[3-8A] Fabrication of porous pure magnesium by MM-SPS process 《 Sintering, Physical Property 》

*Masahiro kUBOTA¹, Takumi INOMIYA¹ (1. College of Industrial Technology, Nihon University)

11:20 AM - 11:35 AM

[3-9A] Surface Coating Layer / M1A Laminate Interface Characteristics of Practical Magnesium Alloy M1A Surface Coating Materials with Alumina Particle Dispersed Magnesium Powders Fabricated Using MM/SPS Method 《 Sintering 》

*Longyi WEN¹, Shigehiro Kawamori¹ (1. Tamagawa Univercity）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)

11:35 AM - 11:50 AM

[3-10A] In-situ X-ray CT observation of the initial stage of monodisperse Cu powder sintering 《 Sintering, Evaluation Technology 》

Makoto Tsuchiya¹, Gaku Okuma², Ryotaro Kusunoki³, Asuka Suzuki³, Masato Hoshino⁴, Masayuki Uesugi⁴, *Yukiko Ozaki⁵ (1. Kyushu University, 2. NIMS, 3. Nagoya University, 4. Japan Synchrotron Radiation Research Institute, 5. Osaka University)

General Session:Forming and Sintering

Tue. Nov 19, 2024 1:10 PM - 2:10 PM Room III (3F, Room 301)

Chairperson:Masahiro KUBOTA(Nihon University)

+Add all to schedule

1:10 PM - 1:25 PM

[3-11A] Evolution of microstructure and defects in sintering of alumina laminates observed by synchrotron X-ray tomography 《 Sintering, Evaluation Technology 》

*Gaku OKUMA¹, Toshio OSADA¹, Fumihiro WAKAI¹, Ryutaro USUKAWA² (1. National Institute for Materials Science, 2. AIST)

1:25 PM - 1:40 PM

[3-12A] Fine microstructures and mechanical properties of Ti-Mo sintered alloy with heat treatment 《 Sintering 》

*Sei MIYAMOTO¹, Shota KARIYA², Junko UMEDA², Katsuyoshi KONDOH² (1. Graduate School of Engineering, Osaka University, 2. Joining and Welding Research Institute, Osaka University ）（※This presenter is a candidate for the Student Award for Outstanding Presentation.　)

1:40 PM - 1:55 PM

[3-13A] Achieving Extraordinary Strength and Toughness in PM Titanium-Molybdenum Alloys 《 Synthesis Process, Sintering, Physical Property 》

*Jeff Huang^1,2, Abdollah Bahador^2,3, Ammarueda Issariyapat², Shota Kariya², Junko Umeda², Katsuyoshi Kondoh² (1. Graduate School of Engineering, Osaka University, 2. Joining and Welding Research Institute, Osaka University, 3. Materials Processing Institute, United Kingdom）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)

1:55 PM - 2:10 PM

[3-14A] Development of Mo-ZrC with suppressed property changes after high temperature heating 《 Synthesis Process, Sintering, Physical Property 》

*Sora UEMATSU¹, Ryota NAKAMURA¹ (1. ULVAC, Inc)

Sessions