一般セッション

射出成形

Thu. Jun 20, 2024 1:30 PM - 2:50 PM Room B (3階　平安)

座長:龍野道宏(東京大学)

+Add all to schedule

1:30 PM - 1:50 PM

[B-205] Effects of thickness and injection molding conditions on mechanical properties of PP dumbbell specimens

*FUMIAKI BABA¹, YOSHIHIRO TAKAI¹, SATOSHI NISHIOKA¹, CHIGUSA NAGANO¹, NORIYUKI FUJII¹ (1. MITSUBISHI ELECTRIC CORP.)

1:50 PM - 2:10 PM

[B-206] Effects of Different Fiber Content on Mechanical Properties and Internal Structure of GFRP Injection Molded Products

*Kippei Futami¹, Senri Hirata¹, Akio Ohtani¹, Yoshimichi Fujii² (1. Kyoto Institute of Technology, 2. Kanazawa Institute of Technology)

2:10 PM - 2:30 PM

[B-207] Influence of flow rate control molding with multi-point gates on tensile elongation at break of PP injection-molded products

*Takuro Fujii¹, Takao Kameda¹, Shigeru Yao², Nobuhisa Takayama² (1. Sanko Gosei Ltd., 2. Fukuoka University.)

2:30 PM - 2:50 PM

[B-208] Mechanical Properties of Starve-fed Glass Fiber Reinforced PBT

*Rie Nobe¹, Satoshi Nagai², Makoto Kudo¹ (1. Akita Industrial Technology Center, 2. Mitsubishi Gas Chemical Trading, Inc.)

一般セッション

射出成形

Thu. Jun 20, 2024 3:20 PM - 4:40 PM Room B (3階　平安)

座長:杉野直人(三光合成)

+Add all to schedule

3:20 PM - 3:40 PM

[B-209] Investigation of adhesive strength by surface treatment on integrated injection Molding

*ATSUSHI MIZUTANI¹, FUMINORI HOSAKA¹, SHINICHI KURODA¹ (1. Nissan Motor Co., Ltd. )

3:40 PM - 4:00 PM

[B-210] Study on Performance of Gas Venting Ejector Pins in Plastic Injection Molding

*Osamu Abe¹, Hikoe Mizukoshi², Hiroyuki Yamada¹, Michiyoshi Nishimura¹, Masaaki Furuya¹, Kazuma Osada¹ (1. Yamanashi Prefectural Industrial Technology Center, 2. Doshi Chemical Industry Co.,LTD)

4:00 PM - 4:20 PM

[B-211] Title: "Precision Joining Technology and Applications of 3D Complex-Shaped injection molding part of Super-Engineering Plastics"

*Tomohiro Miyano¹, Takashi Fujita¹, Hidekazu Murakoshi¹ (1. NISSEN CHEMITEC CORPORATION)

4:20 PM - 4:40 PM

[B-212] Production of direct bonding specimens of metal and resin by the fused filament lamination (FFF) method

*Soma Kojitani¹, Lee Seung Joo², Rajesh Kumar Sharma¹, Kentaro Taki¹ (1. Kanazawa Univ., 2. Gutenberg)

Sessions

一般セッション » 射出成形

射出成形

[B-205] Effects of thickness and injection molding conditions on mechanical properties of PP dumbbell specimens

[B-206] Effects of Different Fiber Content on Mechanical Properties and Internal Structure of GFRP Injection Molded Products

[B-207] Influence of flow rate control molding with multi-point gates on tensile elongation at break of PP injection-molded products

[B-208] Mechanical Properties of Starve-fed Glass Fiber Reinforced PBT

射出成形

[B-209] Investigation of adhesive strength by surface treatment on integrated injection Molding

[B-210] Study on Performance of Gas Venting Ejector Pins in Plastic Injection Molding

[B-211] Title: "Precision Joining Technology and Applications of 3D Complex-Shaped injection molding part of Super-Engineering Plastics"

[B-212] Production of direct bonding specimens of metal and resin by the fused filament lamination (FFF) method

Authentication