一般セッション

紡糸・フィルム成形

Thu. Jun 20, 2024 1:30 PM - 2:50 PM Room C (3階　福寿)

座長:中山昇(信州大学)

+Add all to schedule

1:30 PM - 1:50 PM

[C-205] Effect of molecular weight of low-molecular-weight polyethylene added by reactor blending on melt drawability of ultrahigh-molecular-weight polyethylene

*Ayaka Takazawa¹, Masaki Kakiage¹, Takeshi Yamanobe¹, Hiroki Uehara¹, Shinichi Asai², Shoko Naruke², Takuya Ohnishi², Yasutake Wakabayashi² (1. Gunma Univ., 2. Tosoh Co.)

1:50 PM - 2:10 PM

[C-206] Preparation of homogeneous lamellar membrane of ultra-high molecular weight polyethylene and its large-area spreading by biaxial melt-drawing/shrinking

*Shion Noguchi¹, Ayaka Takazawa¹, Masaki Kakiage¹, Takeshi Yamanobe¹, Hiroki Uehara¹ (1. Gunma Univ.)

2:10 PM - 2:30 PM

[C-207] Fabrication of ultrahigh-molecular-weight polyethylene submicron thin films by solvent-free process

*Masaki Kakiage¹, Ritsuki Harasawa¹, Ayaka Takazawa¹, Takeshi Yamanobe¹, Hiroki Uehara¹ (1. Gunma Univ.)

2:30 PM - 2:50 PM

[C-208] Retardation control by stretching fluorene based polyester film with negative birefringence properties

*Yoshiya Ota¹, Shogo Suga¹ (1. Osaka Gas Chemicals Co., Ltd.)

一般セッション

紡糸・フィルム成形

Thu. Jun 20, 2024 3:20 PM - 4:20 PM Room C (3階　福寿)

座長:引間悠太(産業技術総合研究所)

+Add all to schedule

3:20 PM - 3:40 PM

[C-209] Effect of viscosity ratio on fiber structure and Properties in high-speed spinning of syndiotactic/atactic polystyrene bicomponent fibers.

Yang Yu¹, *Wataru Takarada¹, Shioya Masatoshi¹ (1. Tokyo Tech.)

3:40 PM - 4:00 PM

[C-210] Preparation of Foamed Fibers of Polycarbonate through Laser-Heated Melt Electrospinning

*Ryosaku Azumi¹, Masahiro Abe², Toshiharu Goto², Haruki Kobayasi¹, Katsufumi Tanaka¹, Wataru Takarada³, Takeshi Kikutani³, Midori Takasaki¹ (1. Kyoto Institute of Technology, 2. Maxell, 3. Tokyo Institute of Technology)

4:00 PM - 4:20 PM

[C-211] HILS verification of film tension controller

*Hiroki Hamamoto¹, Tomohiro Hirakawa¹, Keita Hihara¹, Takashi Ochiiwa¹, Takuya Kinoshita², Toru Yamamoto² (1. The Japan Steel Works, Ltd., 2. Hiroshima Univ.)

Sessions

一般セッション » 紡糸・フィルム成形

紡糸・フィルム成形

[C-205] Effect of molecular weight of low-molecular-weight polyethylene added by reactor blending on melt drawability of ultrahigh-molecular-weight polyethylene

[C-206] Preparation of homogeneous lamellar membrane of ultra-high molecular weight polyethylene and its large-area spreading by biaxial melt-drawing/shrinking

[C-207] Fabrication of ultrahigh-molecular-weight polyethylene submicron thin films by solvent-free process

[C-208] Retardation control by stretching fluorene based polyester film with negative birefringence properties

紡糸・フィルム成形

[C-209] Effect of viscosity ratio on fiber structure and Properties in high-speed spinning of syndiotactic/atactic polystyrene bicomponent fibers.

[C-210] Preparation of Foamed Fibers of Polycarbonate through Laser-Heated Melt Electrospinning

[C-211] HILS verification of film tension controller

Authentication